Causes
- VRR luminance flicker while Adaptive-Sync is active. The C27G75T is a 1000R VA panel rated for a variable refresh window of roughly 80–240Hz. When a game drops below 80 fps, the panel cannot follow and the image visibly pulses or dims and brightens. Menus, map screens, loading transitions, and open-world games that swing between 70 and 200 fps are the classic trigger. Turning Adaptive-Sync off is the fastest way to prove this is the cause.
- Firmware older than 1009.3, so the OSD has no VRR Control. The original 2020 firmware flickered badly in dark scenes and at the low end of the VRR range. Samsung added a VRR Control option under System in firmware 1009.3 specifically to damp that fluctuation, so a monitor still on launch firmware will flicker no matter how the GPU is configured.
- HDR left on for SDR content. This is a DisplayHDR 600 edge-lit panel with no local dimming, so HDR is produced by driving the edge backlight harder. With HDR enabled on the desktop or in an SDR game, tone mapping oscillates between two nearly identical brightness levels and the screen pulses, most obviously on white browser pages and dark grey game menus.
- Response Time set to Fastest. At 240Hz the Fastest overdrive pushes VA pixel transitions past their target, and the overshoot shows up as bright flashes on moving edges. In dark scenes this reads exactly like flicker and is often blamed on VRR when the overdrive level is the real problem.
- A marginal DisplayPort link at 240Hz. 2560x1440 at 240Hz needs a clean DisplayPort 1.4 connection. A long or thin cable, an HDMI-to-DP adapter, a KVM, or a connector that is not fully latched makes the link retrain and produces single black frames or a sharp bright flash rather than the slow pulsing typical of VRR.
- Driver-level VRR mismatch. G-Sync Compatible on a FreeSync monitor depends on the NVIDIA driver's handshake, and Windows updates sometimes reset the display to a different refresh rate. Flicker that appeared right after a driver or Windows update usually clears with a clean driver install.
How to Fix
- Confirm that VRR is the trigger. Press the JOG button on the underside of the bezel to open the OSD, go to Game and set Adaptive-Sync to Off. On NVIDIA also open NVIDIA Control Panel → Set up G-SYNC and clear Enable G-SYNC, G-SYNC Compatible. If the flicker stops instantly, the steps below are about keeping VRR usable. If it continues with VRR off, jump to the cable and driver steps.
- Update the monitor firmware, then try VRR Control. Download the current firmware for the LC27G75T from Samsung support, copy the file to a FAT32-formatted USB stick, and update through the monitor's service USB port using System → Software Update. After the reboot, open System → VRR Control and set it to On. This damps the brightness swing in dark scenes; the trade-off is a slight softness in frame pacing, so turn it back off if the stutter bothers you more than the flicker.
- Cap the frame rate inside the refresh window. In each game set a frame limit of about 230 fps at 240Hz and 140 fps at 144Hz instead of Unlimited, and enable NVIDIA Max Frame Rate or AMD Radeon Chill globally. The goal is to stop the rate collapsing below roughly 80 fps and then snapping back, because that swing is what the panel renders as flicker. Capping menus and loading screens matters as much as capping gameplay.
- Stop the rate from collapsing in menus. Many titles render menus at uncapped frame rates and then drop to a cutscene at 30 fps. Set a global driver limit and, where the game allows, enable a background or menu frame cap. Half-rate V-Sync style options also keep the panel out of the unstable low end of the VRR window.
- Turn HDR off for desktop and SDR games. Open Windows Settings → System → Display → HDR, select the G7 and switch Use HDR off, enabling it only for HDR games and video. With HDR off, run brightness in the OSD around 30–45, which keeps the edge backlight away from full output where the oscillation is most visible.
- Set Response Time to Standard. In the OSD open Game → Response Time and choose Standard. Standard is the only level that does not add visible overshoot on this panel; Faster and Fastest trade smear for bright edge flashes that look like flicker during fast motion.
- Reseat or replace the DisplayPort cable. Power everything down, unplug the DP cable at both ends, check for bent pins, and re-seat it until the latch clicks. Use a certified DisplayPort 1.4 cable no longer than 2m, plugged directly into the graphics card rather than through a dock, adapter, or KVM, and try the other DP input on the monitor to rule out a bad port.
- Clean-install the GPU driver. Install the latest driver for your card. If the flicker started after an update, remove the old driver with Display Driver Uninstaller in Safe Mode, reinstall, then re-check the refresh rate in Settings → System → Display → Advanced display before turning Adaptive-Sync back on.
- Test a second source before assuming the panel is faulty. Connect a different PC or console on a different cable and input. Flicker that follows the monitor across two sources, with Adaptive-Sync and HDR off, is a backlight or scaler fault and should go to Samsung as a warranty repair rather than more tweaking.