Causes
- DisplayPort Stream left on 1.2 in the OSD: this is the most common reason a PG32UQ will not go past 60Hz at 4K. The compatibility setting caps the DisplayPort link at a lower bandwidth, so 3840x2160 at 144Hz is never offered. Owners who reset the monitor or update firmware sometimes find it back on 1.2 without noticing.
- An HDMI 2.0 or generic cable on the HDMI 2.1 input: the PG32UQ has two HDMI 2.1 ports, but 4K above 60Hz over HDMI requires a certified Ultra High Speed (48Gbps) cable. An older High Speed cable, a long cable, or an HDMI 2.0 cable negotiates down to 4K 60Hz no matter what the GPU is set to.
- A DisplayPort 1.2 cable or a long passive run: DisplayPort 1.2 carries roughly 21.6Gbps, which is not enough for 4K 144Hz even with compression. A DP 1.2 cable, a cable longer than about 2 m, or an adapter in the chain will train at a lower link rate and hide the 144Hz mode.
- Windows only exposes TV resolutions: NVIDIA Control Panel separates "Ultra HD, HD, SD" TV modes from "PC" modes. The 144Hz entry for the PG32UQ lives under the PC list at 3840x2160, so a user who only checks the default list can conclude the monitor cannot do 144Hz when it can.
- The GPU does not support DSC: DisplayPort 1.4 on Pascal cards such as the GTX 1080 Ti tops out around 4K 98Hz because those GPUs lack Display Stream Compression. Turing, Ampere, Ada, RDNA 2 and later support DSC. On Pascal or an older HDMI 2.0 GPU, 144Hz at 4K is simply not available over DisplayPort.
- Console output limits: a PS5 or Xbox Series X caps 4K output at 120Hz, so a PG32UQ connected to a console will never show 144Hz. The console also needs 4K and 120Hz explicitly enabled in its video settings, or it may stay at 60Hz.
- Driver or EDID problem after an update: a driver update, a monitor firmware change, or a corrupted EDID cache can leave the display at 60Hz with the higher modes missing until the driver is reinstalled or the display is re-detected.
- Signal routed through the motherboard or a dock: plugging into the motherboard's HDMI or DisplayPort output, a USB-C dock, or a capture card often limits the link to HDMI 2.0 or DP 1.2 speeds, so the PG32UQ never sees a 4K 144Hz signal.
How to Fix
- Set DisplayPort Stream to 1.4: open the OSD with the joystick, go to System Setup, select DisplayPort Stream, and choose 1.4. Power-cycle the monitor and reboot the PC. Then check the refresh rate list again before changing any cable, because this fixes the majority of PG32UQ 60Hz cases on its own.
- Use the right cable on the right port: connect the PG32UQ directly to the graphics card with the included DisplayPort cable or another VESA-certified DP 1.4 cable of 2 m or less. Do not use an adapter, extension, KVM, or USB-C dock. For HDMI, use a certified Ultra High Speed HDMI cable and a GPU with an HDMI 2.1 port.
- Pick 144Hz in Windows: go to Settings, System, Display, Advanced display, select the PG32UQ, and set the refresh rate to 144Hz at 3840x2160. If 144Hz is missing, continue to the GPU control panel rather than assuming the monitor is limited.
- Set the mode in the GPU control panel: in NVIDIA Control Panel open Change resolution, scroll to the PC section, select 3840x2160, and choose 144Hz. In AMD Adrenalin open Display and set 144Hz there. This exposes the full PC timing list that the Windows dropdown sometimes hides.
- Enable 10-bit color to confirm DSC: in the same NVIDIA or AMD panel set output color depth to 10 bpc and RGB. At 4K 144Hz this only works when DSC is active. If 10 bpc disappears at 144Hz but works at 120Hz, the link is bandwidth-limited and the cable is still the likely culprit.
- Update monitor firmware and GPU driver: install the latest PG32UQ firmware over the USB upstream cable, then clean-install the latest GPU driver. Firmware updates on this model correct input and EDID handling that can leave the display at 60Hz after a source change.
- Confirm the GPU can actually do it: if you are on a GTX 10-series card or an older APU, 4K 144Hz over DisplayPort is not possible because the GPU lacks DSC. Use HDMI 2.1 if the card has it, accept a lower refresh rate, or move to an RTX 20-series or newer / RX 6000-series or newer GPU.
- Test another source and another cable: connect a laptop, console, or second PC with a known-good cable. A PS5 or Xbox topping out at 120Hz is normal. If every source and cable stays at 60Hz with DisplayPort Stream 1.4, the monitor's input board is faulty and the unit should be replaced or serviced under warranty.