Causes
- HDR is on in Windows but the content is not HDR: when Windows HDR is enabled, ordinary SDR windows and the desktop are mapped into an HDR container. On the PG32UQ that makes the desktop look grey, flat, and dimmer than SDR. This is expected behavior, not a panel fault, and it is the most common reason owners think HDR is broken.
- Windows HDR calibration was never run: without a calibration profile, Windows does not know the PG32UQ's peak brightness (about 600 nits) or its black level. The result is crushed or lifted midtones, clipped highlights, and an overall dull image in HDR games and video.
- The PG32UQ is only DisplayHDR 600 with 16 edge-lit dimming zones: this is a semi-HDR monitor. With so few zones along the edges, dark scenes lift toward grey and bright objects produce visible halos. Owners expecting OLED-style blacks read this as "washed-out HDR", but it is a known limitation of this panel, not a failure.
- HDR Setting is off in the OSD, or the wrong HDR mode is selected: the monitor has its own HDR Setting and HDR Mode in the Image menu. If HDR is off there while Windows is sending HDR, or the mode is set to Cinema HDR while gaming, the image looks flat, over-bright, or oddly tinted.
- The GPU falls back to 8-bit 4:2:2: at 4K 144Hz without DSC, or with DisplayPort Stream set to 1.2, the driver may drop to 8-bit chroma-subsampled output. HDR then shows color banding, dull reds, and soft text. HDR needs 10-bit RGB to look right on this monitor.
- The game's own HDR switch is off or mis-tuned: many games require HDR to be enabled inside the game menu even when Windows HDR is on. A paper-white or peak-brightness slider set too low produces a dim, washed-out image that looks like a monitor problem.
- Shadow Boost or Dynamic Dimming is lifting the blacks: Shadow Boost brightens dark areas for visibility, and Dynamic Dimming adjusts the edge-lit backlight. Used together in SDR or in a dark game, they raise black levels and drain contrast, which reads as washed out.
- HDR is blocked by ELMB Sync or an incompatible mode: ELMB Sync and some Adaptive-Sync combinations cannot run with HDR, and the monitor may silently stay in SDR when both are enabled.
How to Fix
- Enable HDR in both places: in the OSD open Image, set HDR Setting to ON, and choose HDR Mode: Gaming HDR for games, Cinema HDR for films, DisplayHDR for a neutral starting point. Then in Windows go to Settings, System, Display, HDR and turn HDR on for the PG32UQ. HDR only works when both ends agree.
- Run Windows HDR Calibration: install Windows HDR Calibration from the Microsoft Store and run it with HDR enabled. Follow the patterns until the cross is barely visible, then set the peak brightness to about 600 nits for this panel. The profile is saved per display and fixes most dull or clipped HDR complaints.
- Force 10-bit RGB output: in NVIDIA Control Panel, Change resolution, select 3840x2160 at 144Hz, choose Use NVIDIA color settings, set Desktop color depth to Highest (32-bit), Output color depth to 10 bpc, Output color format to RGB, and Output dynamic range to Full. On AMD use 10-bit and RGB Full in Adrenalin. If 10 bpc is unavailable, set DisplayPort Stream to 1.4 and use a certified DP 1.4 cable.
- Turn off ELMB Sync and Adaptive-Sync while testing: in the OSD disable ELMB Sync and Adaptive-Sync, then re-enable HDR and check the image. Once HDR is confirmed working, re-enable Adaptive-Sync if you want VRR, but leave ELMB Sync off for HDR.
- Set Shadow Boost to zero and control dimming: in the OSD set Shadow Boost to Level 0 or 1. For desktop and SDR work, turn HDR off so the monitor runs in SDR and looks normal. For HDR films and games, leave Dynamic Dimming on and accept some halo around bright objects, which is normal for a 16-zone edge-lit panel.
- Tune the in-game HDR sliders: in each game's HDR menu enable HDR, set paper white to roughly 200 to 300 nits, and set peak brightness near 600 to match the PG32UQ. Use the game's calibration pattern if it has one. A paper-white value of 100 or a peak of 1000+ makes the image look dim or blown out.
- Use SDR with sRGB for accurate desktop color: for non-HDR work, turn HDR off in Windows and select the sRGB GameVisual mode in the OSD. This avoids the grey, oversaturated look that comes from running the wide-gamut panel without an HDR or color-managed signal.
- Update firmware and driver, then retest: install the latest PG32UQ firmware over USB and clean-install the GPU driver. Test HDR with a known HDR source such as an HDR video on YouTube or a game with a reliable HDR mode. If HDR still cannot be enabled in Windows with a 10-bit RGB signal and HDR on in the OSD, the input board or panel is faulty and the monitor should be serviced under warranty.