← ACEMAGIC F5A Fix Guide

How to Fix USB4 Ports Not Sending a Display Signal on the ACEMAGIC F5A

💻 Device: ACEMAGIC F5A 🗓 Added

Causes

  • The USB-C cable does not carry DisplayPort alt mode. Both F5A USB4 ports output DisplayPort 1.4 in alt mode, but only a USB-C cable wired for it will negotiate that link. The charge cable bundled with a phone or a cheap USB 2.0 cable powers a dock happily and never passes video, so Windows reports the port as healthy while the monitor stays on "No Signal".
  • The PD input port is being used as an output port. Only one of the two USB4 ports accepts 100W power delivery input; the other is limited to 15W output. Plugging the monitor or dock into the port that is wired for input, or feeding the machine from the wrong port, leaves the display output inactive or the machine running off the external supply's fallback instead of the DC adapter.
  • The USB4 host router driver is missing. Windows 11 needs the AMD USB4 host router driver to enumerate USB4 docks and their downstream displays. On a freshly reinstalled or vendor-imaged system without the chipset package, the port falls back to plain USB 3.2 behaviour and anything behind the dock (display, Ethernet, audio) disappears.
  • Four 8K displays were assumed to work with any adapter. The F5A can drive up to four 8K panels at 60Hz, but only by using Display Stream Compression across its outputs. A USB-C to HDMI 2.1 adapter without DSC support, or a hub that splits one port into three cheap outputs, will drop to a lower resolution or produce no signal at all on the higher-resolution screens.
  • USB selective suspend has parked the port. Windows power management can suspend an idle USB4 port, and some docks and monitors never wake it again. This is the usual cause of a display that works on boot, disappears after the monitor sleeps, and comes back only after a full restart.
  • The display output is disabled or mis-set in the BIOS. The integrated Radeon 890M can have its multi-monitor support or its primary output configuration set in firmware, and a BIOS that was reset after a CMOS clear can leave an output switched off.

How to Fix

  1. Swap to a cable rated for USB4 or Thunderbolt display output. Use a 40Gbps USB4 or Thunderbolt 3/4 cable that explicitly lists DisplayPort alt mode or 8K video support. Test with the cable the monitor or dock shipped with before changing any settings; this resolves the majority of no-signal reports on this machine.
  2. Use the correct USB4 port for each job. Check the labels on the rear panel and plug the 100W PD supply or the power input into the port ACEMAGIC marks for power delivery input, then connect the display or dock to the other USB4 port. If you are powering the F5A from a USB-C charger, use one rated 100W or more with PD 3.0 and confirm the machine does not drop the link when the CPU boosts.
  3. Force Windows to detect the display. Press Win + P and choose Extend, then open Settings → System → Display and click Detect. If the monitor is still missing, open Device Manager → View → Show hidden devices and check Display adapters and Universal Serial Bus devices for an entry with a warning triangle.
  4. Install the AMD chipset and USB4 drivers. Download the current AMD chipset driver package for the Ryzen AI 9 HX 470 from amd.com and install it, then check ACEMAGIC's F5A support page for a USB4 host router driver. Reboot before retesting the port; the dock's display outputs do not enumerate until the host router driver is loaded.
  5. Turn off USB selective suspend and fast startup. Open Control Panel → Power Options → Change plan settings → Change advanced power settings, expand USB settings → USB selective suspend setting and set both On battery and Plugged in to Disabled. Then open Control Panel → Power Options → Choose what the power buttons do and untick Turn on fast startup. This stops the port being parked between sessions.
  6. Test the fixed outputs to separate a port fault from a cable fault. Plug the same monitor into the F5A's HDMI 2.1 or DisplayPort 2.1 output. If that works, the monitor and cable are fine and the problem is confined to the USB4 path; if nothing works on any output, treat it as a graphics driver or BIOS issue instead.
  7. Reset the display stack when the port vanishes after sleep. Press Win + Ctrl + Shift + B to restart the graphics driver without rebooting, and if that recovers the screen, set the monitor's own power saving to a longer timeout or disable it, since the dock is not re-asserting hot-plug detection on wake.
  8. Update the BIOS and re-check the display configuration. Flash the latest F5A BIOS from the ACEMAGIC support page, then enter the BIOS with Del and confirm that integrated graphics output and multi-monitor support are enabled and that the primary display is set to Auto. Save with F10 and test each port again before and after a cold boot.